-
Fender veneers are mainly used to protect docks and ports in areas such as docks and ports. They are mainly used to block the impact of ships on docks and play a protective role. Fender veneers are mainly made of ultra-high molecular weight polyethylene sheets. Due to their unique ultra-high impact resistance, impact resistance, extremely low water absorption and high strength, aging resistance, corrosion resistance Long use time,
Published on: June 12, 2019 Clicks: 113
-
The service life is higher than that of steel, and the wear resistance is 3~7 times of carbon steel and stainless steel; Small friction coefficient, self-lubricating, non absorbent, non cohesive materials, high impact strength, good comprehensive mechanical performance, acid, alkali, salt corrosion resistance, non aging, low temperature resistance, health, non-toxic, light weight, 1/8 of steel, therefore, it is used as bulk materials
Published on: June 12, 2019 Number of hits: 32
-
Performance characteristics of wharf fender plate: service life is higher than steel, and wear resistance is 3~7 times of carbon steel and stainless steel; Small friction coefficient, self-lubricating, non absorbent, non adhesive materials, high impact strength, good comprehensive mechanical performance, acid, alkali, salt corrosion resistance, non aging, low temperature resistance, sanitary, non-toxic, light weight, steel specific gravity
Published on: June 12, 2019 Number of hits: 30
-
Explanation of terms: rubber fenders are installed at the front of wharves and hydraulic structures. They are made of rubber materials in various shapes and are shock proof devices that can isolate and absorb energy.
Published on: June 12, 2019 Clicks: 77
-
1. Thermal insulation performance: thermal conductivity of polyurethane is 0.022W/(m · K), EPS is 0.041W/(m · K), XPS is 0.028W/(m · K). 2. Tightness: EPS and XPS are bonded with seams and cavities, and the external air can easily flow through the seams and cavities, affecting the insulation performance. If the factor that there are gaps in the cavity is taken into account
Published on: June 11, 2019 Clicks: 42
-
We often see that some design units point out in the technical specification of anti-corrosion coating that polyurethane finish or acrylic polyurethane finish should be used as the finish paint, and then the paint purchasing unit makes an inquiry from the paint manufacturers according to this name in the inquiry list, but the prices quoted by the manufacturers are different, or even several times different. Why? This is because there are many kinds of polyurethane finish
Published on: June 11, 2019 Number of hits: 70
-
Soft polyurethane foam refers to soft polyurethane foam plastic, which is a flexible polyurethane foam plastic with certain elasticity. It is a polyurethane product with the largest amount of polyurethane products. The polyurethane soft foam is mostly of open cell structure, which has low density, good elastic recovery, sound absorption, breathability, heat preservation and other properties. It is mainly used as furniture cushion, mattress, vehicle seat cushion and other cushion materials
Published on: June 11, 2019 Clicks: 91
-
The excellent polyurethane PU board commonly used thermal insulation materials include: rock wool, glass fiber wool, polystyrene), integrated houses, steel structure workshops, etc., which have good thermal insulation effect. High strength polyurethane PU board uses high strength steel plate as the base material (with high tensile strength), plus the most advanced design and roll forming. Therefore, the polyurethane PU board mobile house has excellent structural characteristics. Below
Published on: June 11, 2019 Number of hits: 27
-
Polyurethane is an important synthetic polymer material, especially polyurethane foam is widely used in furniture, building energy conservation and other fields. However, polyurethane not only needs non renewable petroleum resources as raw materials in the production process, but also is difficult to be recycled after use, which is not conducive to sustainable development. A new study is expected to change this situation. The synthesis of polyurethane requires polyols and isomers
Published on: June 11, 2019 Number of hits: 29
-
Thermoset soft foam and elastomer have certain thermal softening plasticity at 100-220 ℃, which can achieve mutual bonding without using adhesive. Combined with the subsequent molding steps, uniform recycled products can be obtained, which is hot pressing. Bayer (now Covestro) has developed a recycling process for waste elastomer products, crushing waste into particles for preheating,
Published on: June 11, 2019 Clicks: 439
-
Sustainable development has always been the focus and inevitable development trend of the chemical industry. In the era of pure pursuit of maximum benefits, the development model of "waste water, waste water and waste water", global warming, resource tension and other serious problems have been brought about by the development model of "waste water, waste water and waste water". The increasing large-scale environmental pollution problems have caused people's concern about the deterioration of the living environment and the earth's climate. In the new era, sustainable development is not new
Published on: June 11, 2019 Number of hits: 277
-
The full name of polyurethane foam adhesive is one component polyurethane foam sealant, commonly known as foaming agent, foam adhesive, PU sealant, in English, PUFOAM, which is the cross combination of aerosol technology and polyurethane foam technology. Polyurethane foam adhesive is a special polyurethane product that can be filled with polyurethane prepolymer, foaming agent, catalyst and other components in a pressure resistant aerosol tank. When the material is discharged from the aerosol tank
Published on: June 11, 2019 Clicks: 409
-
Polyurethane has two main raw materials, isocyanate (including TDI, MDI, PIDI, HDI, etc.) and polyether polyol. Among them, isocyanate is relatively toxic, especially TDI is recognized as toxic, carcinogenic and irritating. In addition, other ingredients used in the foaming process mainly include: 1. Catalyst, mainly amine catalyst and tin catalyst. Amine catalysts
Published on: June 11, 2019 Number of hits: 501
-
Polyurethane itself is non-toxic, but no material can be 100% pure. Polyols, isocyanates, surfactants, catalysts, foaming agents and some functional additives are required for the synthesis of polyurethane foam
Published on: June 11, 2019 Number of hits: 466
-
For all kinds of articles in life, our feelings about them are intuitive, such as the concepts of hardness, elasticity, toughness, brittleness, etc. This information obtained through intuitive feeling and perception is generally called qualitative judgment. Qualitative judgment is usually vague, imprecise and not conducive to comparison. Just as we know that iron is hard and steel is hard, which one is harder, except for the two
Published on: June 11, 2019 Clicks: 262
-
Under the new economic normal, rubber and plastic sealing enterprises have accelerated their transformation, constantly looking for new development opportunities in the Internet platform, overseas markets, etc., and achieved certain results, most intuitively reflected in the increase of operating income. According to the 2016-2020 Research Results of China's Silicone Industry released by Linghe. com, the silicone sealing strip has the following characteristics: 1. Good sealing performance of silicone material
Published on: June 11, 2019 Number of hits: 38
-
Silica gel products, as environment-friendly materials, have been widely used in various fields. At the same time, they are also being upgraded from molded products to foamed products in more fields. However, the application of traditional foaming agent AC in silica gel foamed products will produce ammonia and formamide, and the foaming agent OBSH will also smell of sulfur and benzene after foaming. Dongguan Haojun Rubber&Plastic Co., Ltd. is up to date on the above issues
Published on: June 11, 2019 Number of hits: 50
-
The foam board foams evenly, with a density of 0.25-0.85g/cm3 and a Shore hardness of 8-30A. Environmentally friendly, non-toxic, odor free, good resilience, good flexibility, no bubbles or pores on the surface. The foamed silicone rubber plate has high strength, long service life, high temperature resistance up to 300 ℃ and no deformation for long-term use. Foamed silicone rubber plate is environmentally friendly, resistant to high and low temperatures, compression and
Published on: June 11, 2019 Number of hits: 33
-
What is a ship fender? Fender, also known as ship fender, is an elastic buffer device used at the edge of wharf or ship, which is made of wood and rubber. It is mainly used to reduce the impact force between ships and docks or between ships in the process of docking or mooring, and prevent or eliminate the damage of ships and docks. Introduction to various types and characteristics of rubber fenders 1)
Published on: June 11, 2019 Number of hits: 43
-
With the continuous development of the global shipping industry and the scale of naval vessels in various countries, the application of high-performance fender systems has become more and more extensive. Ordinary wooden piles and tires have long been unable to meet the demand for berthing. At present, elastic bodies such as rubber, foam foam, air bags, polymer plastics, hydraulic cylinders and other elastic bodies are mainly used as energy absorbing materials, and intelligent fender systems with the function of monitoring shore impact have emerged. Matching
Published on: June 11, 2019 Number of hits: 43
